Constraint systems are made of a small number of primitive shape types; points, lines, circles, two kinds of circular arc, and guides. This topic describes each of them, how they are drawn, and how they behave when dragged. It also explains the difference between regular and construction geometry.
For an overview of constraints and how they are implemented in Grasshopper 2, see the Constraint Systems topic.
Points
Points are the foundation of every constraint system. Every line, arc and bend has a point at each end, and circles and arcs have a point at their centre. Points can also be placed on their own using the Point tool, which is useful for marking locations that other shapes are constrained to, or locations that should be included in the output.

A fixed point is anchored to a location and is drawn as a diamond. The solver never moves fixed points, but they can still be dragged by hand, or—when named—driven by a component input. The exception to this is the origin point, which is drawn as a pink square. It can never be moved, and therefore provides a good anchoring point for the rest of the drawing.
Points can be joined using the Coincident constraint, which forces both points to share the same coordinates. When several points sit in the same place, clicking on them shows a selection menu. This can become very annoying very quickly, which is why the Simplify option in the editor gear menu merges coincident points.
Lines
A line is a straight segment between two points. Lines are drawn by clicking their start point and then their end point. Holding Shift while clicking the end point makes the line exactly horizontal or exactly vertical, whichever is closer, and adds the appropriate constraint.
Lines can be dragged either by the end-points, or from the interior which moves both end-points simultaneously.

Arcs
An arc is a part of a circle, defined by a centre point, a start point and an end point. It is drawn by picking those points in that order. Both end points always lie on the same circle around the centre, and the arc always runs anticlockwise from its start to its end. The radius of an arc can be modified in the editor by dragging the curve segment rather than any of its points.
An unconstrained arc has five degrees of freedom rather than six, since the points are not fully independent of each other.

An arc never flips over from one side to the other as there is no way to smoothly move the centre point across. The flatter an arc becomes, the further away the centre point must travel. Arcs are therefore the natural choice for round shapes whose centre matters, such as the rounded corners of a rectangle.
It is possible to insert fillet arcs into a drawing by holding Shift while the Arc tool is active and clicking on a point where two lines meet.
Bends
To mitigate the no-flipping limitation inherent to arcs, the Grasshopper 2 constraint solver introduces an arc variant called a bend. Unlike arcs, a bend has no centre point but is instead defined by its end points and a bulge factor. This factor can be adjusted manually by dragging the bar in the middle of the bend.

Unlike an arc, a bend can flatten out into a straight line and then curve towards the other side. This makes bends the natural choice for shapes whose ends matter more than their centre, such as a curved edge between two corners which should be allowed to bulge either inwards or outwards depending on an input.
The flexibility of bends comes at a price. As a bend flattens, its centre moves further and further away, until it is infinitely far away at the moment the bend is perfectly straight. Constraints which involve the centre of a bend, such as concentricity, therefore misbehave as the bend approaches a straight line.
Circles
A circle is defined by a centre point and a radius. It is drawn by picking the centre and then a point on the circumference. Dragging the centre of a circle moves it, while dragging its rim makes it bigger or smaller.

Guides
A guide is an infinite line, usually horizontal or vertical, placed with a single pick. Guides are always considered construction geometry, so they are never outputted; they only exist to constrain other shapes. Guides can be either free or fixed, and double-clicking a guide sets its intercept with the associated drawing axis. Angled guides can be created by assigning an Angle constraint.

Construction Geometry
Oftentimes a constraint drawing requires shapes whose only purpose is to allow a specific constraint to be applied correctly. For example a circle enforcing a fixed separation between two shapes, or a line limiting the motion of a point to an axis. Construction shapes are only of interest within the constraint system so they are not included in the Edges output of the component.

Double-clicking a curve with the Select tool switches it between regular and construction geometry.